Food and beverage facilities are hard on floors. Hot washdowns, grease, sugars, acids, constant forklift traffic, and standing water in areas that never fully dry. In these environments, concrete grinding and surface preparation for commercial kitchens, breweries and food production is not a preliminary step before the "real work" of coating — it is the real work. The coating that goes down on top is only ever as good as the surface underneath it, and the surface underneath it is only as good as the mechanical preparation that preceded it.
This page covers what proper preparation involves in food and beverage facilities, why most coating failures trace back to preparation rather than product, and how to read a quote that quietly leaves the grinding out.
A coating in an office or retail space mostly has to survive foot traffic. A floor in commercial kitchens, breweries and food production has to survive a much more aggressive set of conditions:
The common thread: in these facilities, failure is expensive, disruptive, and often happens during production. Which is why preparation deserves more attention, not less.
Concrete grinding and surface preparation is a mechanical process, not a chemical wipe-down. On a typical food and beverage project it includes:
1. Assessment of the slab. Before anything else: What is the concrete like? Is there an existing coating, sealer, adhesive or contamination to remove? Are there cracks, joints, spalling or past patch repairs that need addressing? What is the moisture condition of the slab?
2. Mechanical grinding. Diamond grinding removes the weak, laitance-covered surface layer and opens the concrete so a coating can mechanically key into it. The target profile depends on the coating system specified — a thin film coating and a heavy-duty screed need different surface profiles, and the grinding is adjusted accordingly.
3. Repair. Cracks, joints, holes and damaged areas are repaired with appropriate fillers and patching compounds before coating. In wet areas and around drains, repairs also need to be watertight, not just cosmetic. Skipped repairs show up as visible defects and failure points within months.
4. Moisture assessment. Moisture vapour moving through a slab is one of the most common causes of coating failure in food and beverage buildings, particularly in older slabs without effective damp-proof membranes. Where moisture is a risk, it needs to be identified before any resin is opened — because the answer may be a moisture-tolerant primer or a vapour barrier system, not a standard coating that will blister off in a year.
5. Cleaning and verification. Dust and residue are removed, and the prepared surface is checked before coating application begins.
When a floor coating peels, bubbles or wears through prematurely, the product itself is rarely the cause. Epoxy and polyurethane coatings from reputable manufacturers are well understood materials. What varies enormously between a floor that lasts and a floor that fails is what happened to the concrete before the coating was applied.
A coating applied over unground, contaminated, unrepaired or moisture-affected concrete will fail — the only question is when. Failure usually appears as delamination, blistering, or wear that concentrates where the surface was weakest. By then, the cost of the failure is the original job plus the repair job, plus the downtime of doing it twice in a production facility.
When comparing quotes, look at what each one actually includes. A quote that lists "prep" as a single line item or omits grinding, repair and moisture assessment altogether is not a cheaper version of the same job. It is a shorter-lived job with the invoice arriving later.
A properly scoped quote for these facilities should specify: the grinding method and target profile, the repair works included, how moisture is being assessed and managed, the coating system and number of coats, and the expected cure and return-to-service times around your production schedule.
We provide a written warranty on workmanship for installed floors — ask about it when comparing quotes, and note that a contractor willing to put their workmanship in writing is usually one who takes preparation seriously.
For a broader look at flooring across food and beverage environments — including coating systems, coving, line marking and hygiene considerations — see our food and beverage industry overview.
If you are planning a floor project in a commercial kitchen, brewery or food production facility, submit the quote form on this website. Include your facility type, approximate floor area, current floor condition, and any production constraints on timing. We will come back with a properly scoped proposal — preparation, repairs, moisture management and coating system included, so you can compare like for like.