Flake and Chip Epoxy Floors: what to expect on the day

If you're researching flake and chip epoxy floors: what to expect on the day is probably your last question before you decide whether it's worth booking. Fair enough. The process is straightforward, but it runs to a schedule, and knowing that schedule helps you plan around it. Here's how a typical install day actually unfolds, what we need from you, and what the floor will and won't be ready for afterwards.

Before the day

The blend choice happens before install day, and it happens from physical samples, not from a screen. Flake blends look different in person than on a monitor — the chip sizes, density, and colour balance don't translate well to a photo. We bring sample boards or you view them at our location, you pick the blend and the coverage level (full broadcast versus partial), and that's locked in.

The space also needs to be clear. Vehicles out of the garage, items off the floor, walls and shelving accessible where we'll be cutting in. We handle the rest.

Step one: surface prep

This is the part that decides how long the floor lasts, and it's where most of the day goes. We grind the concrete mechanically to open the surface and remove old coatings, cure compounds, and contamination. Cracks and pits get repaired. Then we vacuum the slab properly — dust control matters as much here as anywhere.

On a standard two-car garage, prep typically takes a few hours. If the slab has heavy oil staining, prior coatings, or moisture issues, it takes longer. We'd flag that at quote stage, not on the day.

Step two: base coat and flake broadcast

Once prep is done, we roll the coloured base coat and broadcast the flake blend into it while it's wet. The flakes are tossed by hand, section by section, until the floor reaches the coverage level you chose. Full broadcast means the base coat is completely hidden under chips; partial broadcast lets more of the base colour show through.

Because the flake sits proud of the surface, flake and chip epoxy floors read as less slippery than a smooth-coated floor — the texture gives your shoes something to grip, even when the floor is wet. That's the practical reason flakes are popular in garages, workshops, and commercial spaces, beyond the look.

Step three: scrape and seal

After the base coat cures — usually overnight, so this may run into a second day — the floor is scraped flat to knock down any loose or standing flakes, then vacuumed again. Then comes the clear topcoat, which locks the flakes in and gives the floor its final sheen and chemical resistance. Some jobs take two topcoats; it depends on the space and use.

Cure times and getting back to use

Foot traffic is usually fine a day or so after the topcoat. Vehicles and heavy items need longer — typically a few more days before you park on it or roll equipment across it. We give you specific times for your job in writing, because temperature and humidity affect cure, and a generic number isn't always right.

The honest summary: you lose use of the space for a couple of days, and full heavy use takes roughly the better part of a week. Plan around that.

What drives the cost

We don't quote firm numbers in a general article because every slab is different, but the cost drivers are consistent:

If you want a broader overview of the system itself — flake types, blends, and where it makes sense — see our pillar page on flake epoxy floors.

Workmanship warranty

Every installed floor is covered by a written warranty on workmanship. What that covers, and for how long, is spelled out in the document you get with your job — we don't rely on verbal assurances, and neither should you when comparing installers. Ask any contractor you're considering what theirs covers in writing.

The short version

One day of prep, base coat, and flake. Overnight cure, then scrape and topcoat. Light foot traffic within a day or two of the final coat, heavier use after the full cure window. Clear the space beforehand, pick your blend from samples, and expect a floor that's textured, easy to clean, and noticeably less slippery than a smooth coat.


Ready to get a firm quote? Fill in the quote form on our website with your space details and photos of the slab. We'll assess the condition, confirm which flake blends suit your space, and give you a written price and timeline — no obligations, no phone tag.