Most of the common mistakes with epoxy floor repair and recoat projects come down to one thing: a recoat was done when the floor actually needed to be taken back to concrete. A recoat is the right answer for a worn but sound coating. It is the wrong answer for a floor with failing adhesion, moisture problems, or contaminated concrete. The trouble is that some contractors skip the assessment and quote a recoat over the phone, then discover the real condition of the floor partway through the job — or worse, never discover it at all, and leave you with a floor that peels within a year.
That diagnosis should happen before any work is agreed, not during it. If nobody has checked the floor properly before quoting, treat that as a red flag.
This is the big one. A recoat bonds to whatever is underneath it. If the existing coating is already losing adhesion, the new coat inherits that problem — you have just paid to lock the failure in.
Signs a coating has failed at the bond line include hollow-sounding spots when tapped, lifting at edges and joints, and sheet-like peeling. A proper epoxy floor repair and recoat starts with adhesion testing and a soundness check. If large areas are delaminating, the honest answer is mechanical removal back to bare concrete and a full re-install. Smaller isolated failures can sometimes be spot-repaired and then recoated, but someone has to check first.
Concrete wicks moisture from the ground. If a floor shows blistering, whitish bloom under the coating, or adhesive failure in patterns that follow the slab, moisture vapour is a likely cause. Recoating over it seals the problem in and guarantees a repeat failure.
The fix is testing the slab before the work starts. Where moisture is high, the options are a moisture-tolerant primer, an epoxy moisture barrier, or in severe cases addressing the source. Skipping this step to save a day of prep is the most expensive shortcut in this trade.
A recoat needs a clean, profiled surface — usually a mechanical grind or shot-blast of the existing coat, not just a degrease and a mop. Contaminants like oil, silicone, tyre rubber, and old wax all block adhesion. Thin solvent wipes do not remove them.
Preparation is typically the largest share of the labour cost in an epoxy floor repair and recoat, and it is where quality is won or lost. If a quote seems cheap compared to others, ask exactly what preparation is included. "Cleaning" and "grinding" are not the same thing.
Patching a damaged area with whatever filler is on the van often shows through the recoat as colour or gloss differences, or worse, cracks out because the patch and the slab move differently. Repairs should use materials compatible with the coating system and the substrate, applied at the right thickness and cured fully before recoating.
Not every floor with "epoxy" written on the invoice actually has epoxy on it. Some are urethane, acrylic, or sealer coats. Recoating over an incompatible existing system can cause lifting, wrinkling, or poor cure. Identifying the existing coating — by history, solvent test, or removal test in an inconspicuous spot — is part of a proper assessment.
Verbal scope agreements are where disputes start. A written scope should state what preparation will be done, what happens if the floor turns out to need stripping, and what warranty applies. On installed floors we provide a written warranty covering workmanship, and we stand behind it. If a contractor will not put the scope in writing, that tells you something.
Epoxy needs time to cure before it takes traffic, and foot traffic, forklifts, and hot-tyre pickup all have different waiting requirements. Trying to hand the floor back early is a common way to ruin a technically good job. Plan downtime into the project instead of fighting it.
Ask for an on-site assessment before you accept any quote. Ask specifically: is the existing coating sound, was the slab tested for moisture, and what preparation method is specified? A contractor who can answer those three questions plainly is a contractor who has actually looked at your floor. For how the full repair-and-recoat process works, see our main guide: Epoxy Floor Repair and Recoat.
If your floor is peeling, dulling, or showing wear, the first step is finding out whether it needs a recoat or a full strip-and-reinstall — before anyone quotes you. Submit the quote form on our website and we will assess the floor and give you a written scope, including which mistakes above apply to your situation and what it will take to avoid them.