If your resin floor is worn, peeling, or lifting where forklift tyres turn, an epoxy floor repair and recoat in Westland MI can often bring it back without the cost and downtime of a full replacement. The key word is often. Some floors are candidates for a recoat. Others need to be taken back to bare concrete before anything new goes down. We tell you which one you have before the work starts — not halfway through.
What We Assess Before Recommending a Recoat
An epoxy floor repair and recoat only works if the existing coating is still bonded well enough to build on. On every site visit we check:
Adhesion. We test for hollow-sounding or loose areas by sounding the floor. If coating is debonded in patches, those patches get cut out and repaired before any recoat.
Contamination. Oil, grease, silicate bleed, or old sealers will stop a new coat bonding. Some contamination cleans off. Some means grinding back further than a simple recoat allows.
Moisture. Excess moisture vapour through the slab will push a new coating off, no matter how well it's applied. If moisture readings are high, a recoat is the wrong answer and we'll say so.
Thickness and build history. Floors that have been recoated several times can get too thick, leading to brittleness and further lifting.
Common Problems We Repair
Most of the commercial and industrial floors we repair and recoat in Westland MI show one or more of the following:
Hot tyre lift. Forklift and vehicle tyres heat up and pull soft or under-cured coatings off in arcs, usually at turning points in aisles and loading areas.
Peeling and flaking. Usually a surface preparation failure from the original installation — the coating never bonded properly to the concrete.
Impact damage and spalling. Dropped loads, pallet corners, and chipped joints that need re-profiling before recoating.
General wear and scratches. Traffic-polished, dull floors that are structurally sound but look past their best.
When a Recoat Is the Wrong Answer
We'd rather lose a job than recoat a floor that will fail again in a year. If the existing coating is failing across large areas, if the slab itself is damaged or contaminated, or if moisture is unmanaged, the honest recommendation is to remove the coating entirely and start again. That's a bigger job and a bigger number, and it gets quoted as such up front. For a fuller breakdown of how we approach damaged resin floors, see our page on epoxy floor repair.
How the Repair and Recoat Process Works
Assessment and honest scope. We inspect, test, and tell you what the floor actually needs — recoat, repair, or strip and restart.
Preparation. Diamond grinding or shot blasting to create a profile the new coating can key into. Loose coating is cut out; joints and damaged areas are repaired and re-profiled.
Recoating. Primer (where needed), build coats, and a finish coat suited to your traffic — solid colour, epoxy, or polyaspartic topcoat depending on use and downtime available.
Cure and handover. We tell you when the floor can take foot traffic, forklifts, and hot tyres, and we put the workmanship terms in writing.
Cost Drivers and Ranges
We don't publish firm prices because every floor is different. What drives cost:
Square footage and how much of it needs repair versus recoat
Extent of preparation required
Number of damaged areas needing cut-out and re-profiling
Coating system selected and number of coats
Whether work has to be phased around your operating hours
Small localized repairs sit at the low end; full-floor recoats with extensive preparation sit higher. You get a written, itemized quote before anything starts.
Serving Westland and Nearby
We work with commercial and industrial properties throughout Westland, MI and the surrounding communities. Every floor we install is backed by a written warranty on workmanship — honoured, not just printed.
Get a Quote
If your epoxy floor is peeling, lifting, or simply worn out, tell us what you're seeing. Fill out the quote form on this website with your location, approximate square footage, and a description of the damage. We'll assess the floor honestly and give you a straight answer — recoat, repair, or replace.