If your existing resin floor is looking tired — scuffed, dull, peeling at the edges, or lifting where forklift tyres turn — epoxy floor repair and recoat in Redford MI is often the most cost-effective way to bring it back without tearing everything out and starting over. But it only works when the existing floor is a sound base. Part of our job is telling you honestly which situation you're in before any work starts, not halfway through the job.
This page covers how we approach repair and recoating for commercial and industrial properties in Redford, Michigan, what we can fix, and when a recoat is the wrong answer. For the full range of repair services, see our epoxy repair overview, or visit our Redford service area page.
What We Repair and Recoat
Most recoat projects we handle fall into a few categories:
Worn or dulled surfaces. Traffic polish, light scratching, and loss of gloss in aisles and loading zones. A mechanical preparation and fresh topcoat restores appearance and wear resistance.
Peeling or flaking coating. Usually caused by poor original surface preparation or moisture issues. Loose coating has to be removed back to a sound bond line before recoating — you can't coat over failure.
Hot tyre lifting. Where vehicle tyres have pulled the coating off the slab, typically in garages and service bays. The affected areas get repaired and the whole floor recoated so it matches.
Damaged or out-of-level sections. Cracked, spalled, or pitted concrete under the coating is patched and re-profiled so the recoated floor sits flat and safe for wheeled traffic.
Colour or line changes. A recoat is also the natural time to update safety lines, walkways, or floor colour to match current operations.
When a Recoat Is the Wrong Answer
Sometimes a recoat just doesn't work, and we'll tell you that before you spend money on it. The main situations:
The original coating was never properly bonded. If the existing floor lifts easily across large areas, coating over it just moves the failure date. The floor needs taking back to bare concrete and redoing.
Moisture vapour problems in the slab. If moisture is pushing the coating off, a recoat over the top fails the same way. The slab needs moisture testing and a proper mitigation approach first.
Contamination that can't be fully removed. Oils, chemicals, or previous coatings that won't prepare out cleanly will compromise any new coat.
We'll walk the floor with you, explain what testing we've done, and give you the honest option — even when that means a bigger job than you asked for. You get the assessment in writing before work starts.
How the Process Works
A typical repair and recoat runs like this:
Site walk and assessment. We look at the failure mode, check bond, and test moisture where relevant.
Recommendation in writing. Repair and recoat, partial redo, or full strip and re-coat — with reasoning.
Preparation. Mechanical grinding or shot blasting to create a sound, profiled surface. Failed areas removed and repaired, low spots filled, cracks patched.
Recoating. Primer where needed, build coats as required, then the topcoat — with the slip resistance, colour, and line marking you specify.
Cure and handover. We tell you when the floor can take foot traffic and when it's ready for forklifts.
Cost Drivers
We don't quote firm prices without seeing the floor, because the variables matter: total square footage, how much of the coating has failed, whether repairs or re-profiling are needed, moisture conditions, and the coating system specified. A straightforward recoat on a sound, well-bonded floor costs meaningfully less than a floor that needs strip-back and concrete repair. We'll give you a clear breakdown of what's driving the number.
Workmanship Backed in Writing
Floors we install or recoat are covered by a written warranty on workmanship — the terms are spelled out, and it's honoured. You're not relying on a verbal assurance.
Get a Quote
If you've got a worn, peeling, or damaged epoxy floor at a commercial property in Redford, use the quote form on our website. Tell us roughly where the floor is, its approximate size, and what's going wrong with it. We'll arrange a site visit and give you a straight answer on whether repair and recoat is the right call — or whether it needs something more.