What hot-tyre pickup is and how to avoid it

If you manage a warehouse, workshop, or service facility with a coated concrete floor, sooner or later you'll deal with hot-tyre pickup — the dark rubber marks or actual coating damage left behind where vehicles park or turn. Understanding what hot-tyre pickup is and how to avoid it comes down to three things: coating choice, surface preparation, and cure discipline. This page walks through each one in plain terms.

What hot-tyre pickup actually is

Hot-tyre pickup happens when a tyre heats up during driving, softens, and bonds to the floor coating. When the vehicle moves again, the tyre can pull coating material off the slab, leaving gouged patches, rubber deposits, or both. Two things make it worse:

There's a distinction worth knowing: rubber transfer (black marks you can often clean off) is a maintenance issue. True pickup — where the coating itself tears away — is a coating and installation issue. Fixed-wheel spots, tight turning areas, and loading zones see the most damage because tyres sit hot and stationary in the same footprint.

Why it happens: the usual culprits

In our experience reviewing failed floors, the same causes come up again and again:

  1. Inadequate prep. Coating over polished, sealed, or oil-contaminated concrete. Without proper mechanical profiling, the bond is weak from day one.
  2. Wrong product for the traffic. Thin decorative coatings in areas meant for forklifts and hot car tyres.
  3. Rushed return to service. Putting vehicles on a floor before the coating reaches full chemical cure, not just foot-traffic hardness.
  4. Cheap two-part mixes done wrong. Off-ratio mixing or poor site conditions (cold slab, high humidity) leave a coating that never reaches designed hardness.

How to avoid it

1. Choose the right coating system

For areas with vehicle traffic, use a concrete floor coating engineered for tyre contact — typically a high-build epoxy base with a polyurethane or polyaspartic topcoat, or a full polyaspartic system. The topcoat matters most: harder, more abrasion-resistant finishes resist the mechanical grip of hot rubber. Decorative thin-film epoxies belong in storage rooms and light-traffic areas, not drive aisles.

2. Insist on proper preparation

Mechanical grinding or shot-blasting to a sound, profiled surface is non-negotiable. The coating can only bond as well as the surface under it. Any contractor who proposes rolling epoxy over an untouched slab is setting you up for pickup and peeling later.

3. Respect cure times

Foot traffic in 24 hours doesn't mean tyre-ready. Full chemical cure commonly takes several days to a week depending on product and temperature. Ask for the manufacturer's full-cure window in writing and plan your re-occupancy schedule around it, not around optimism.

4. Manage the hot spots

Even a good floor benefits from operational fixes: avoid letting vehicles sit in one spot immediately after hard driving, keep turning radii wide where possible, and clean rubber deposits promptly so they don't bake in.

Fixing a floor that already has pickup

If you've already got damaged patches, don't just recoat over them — the weak bond transfers to the new layer. Proper repair means grinding back to sound coating or bare concrete, feathering edges, then reapplying the full system to the patched area or the whole zone. In floors with widespread pickup, a full strip and recoat is usually cheaper over a few years than repeated spot repairs.

What this costs

Pricing varies by region, slab condition, and product, so treat these as drivers rather than quotes: total cost rises with prep intensity, film thickness, number of coats, and downtime constraints (nights or weekends add labour cost). Repairing isolated pickup patches is the low end; full removal and recoat of a warehouse slab is the high end. A proper assessment of the slab and the failure pattern is the only reliable way to scope it.

Workmanship and warranty

Installation quality is the biggest variable you control when choosing a contractor. Our installed floors are backed by a written warranty on workmanship — not a verbal assurance — so if the coating fails because of how it was applied, the fix is documented and honoured.

Get an assessment

If hot-tyre pickup is showing up on your floor, or you're specifying a new coating and want it done right the first time, send us the details through the quote form on our website. Include the facility type, traffic profile, and photos of any damaged areas, and we'll come back with a scoped recommendation.