If you manage a facility with a concrete slab, you already know the surface never stays perfect. The real question isn't whether you'll see cracks, pits and spalling: what gets repaired first is the question that determines whether your next floor coating lasts ten years or two. This guide walks through a practical triage order, so you can sequence repairs sensibly and get the slab ready for an epoxy flooring or concrete floor coating system without wasting budget on the wrong fixes at the wrong time.
Coatings fail where the slab is moving, wet, or contaminated. Repair in this order: anything structural or moisture-related first, then contamination and surface prep, then cosmetic cracks and pits last. Jumping straight to cosmetic patching before you've dealt with water or movement is the most common (and most expensive) mistake we see.
Wide cracks (generally anything over roughly 3 mm), cracks that are growing, cracks with one side sitting higher than the other, or cracks that reappear after being filled — these are movement cracks. They indicate the slab is working, not just that it shrank once.
Why they go first: a rigid coating bridged over a moving crack will split along that line, usually within the first year. A flexible joint or crack repair done properly now protects everything above it later.
What to expect: crack repair cost is driven by length, width, accessibility, and whether the crack needs routing and filling versus simple gravity-fed filler. Straight runs are cheaper than a web of hairline fractures that need individual attention.
Spalling often isn't a surface problem — it's a water problem. If spalling clusters near doorways, loading docks, wash bays, or anywhere water pools, fix the water source before the slab. That can mean drainage, downpipe routing, or a vapour barrier question if the slab sits on damp ground.
A concrete floor coating installed over a slab with active moisture drive will blister or delaminate. Any reputable installer will want to assess moisture before quoting a coating system; expect that conversation rather than a simple price-per-square-metre number.
Once movement and moisture are handled, spalled areas get repaired. Spalling is broken, flaking concrete — often where the surface has separated from the aggregate or where rebar corrosion has pushed the cover concrete off.
The repair decision is depth-driven:
Cost drivers: area, depth, edge quality (clean square edges hold patches far better than feathered ones), and how much loose material needs removal first.
Pits — small surface voids from freeze-thaw, aggregate pop-out, chemical attack, or heavy point loading — matter mostly as a surface-prep issue. Individually they're minor; spread across a high-traffic aisle they telegraph through thin coatings and leave a dimpled finish.
Pits are typically filled during the priming and filling stage of an epoxy flooring installation rather than as a standalone repair. If pitting is isolated to traffic lanes, spot-filling those lanes before coating is usually enough. Widespread shallow pitting is often handled more economically by a slightly thicker build coating system than by filling every hole individually.
Hairline shrinkage cracks that aren't moving and aren't leaking get filled last, or in some cases simply get coated over with a system chosen for that slab. They're cosmetic. Don't spend structural-repair money chasing every hairline — but do tell your contractor where every crack is, because hairline cracks can show through (or "picture-frame") under some coatings, and the system choice should account for them.
Before requesting quotes, walk the slab and note:
Photograph everything with something in frame for scale. It speeds up quoting and avoids surprises on the day.
The right sequence is: structural and moisture work → grind and prep → spall and pit repairs → primer and filling → coating. Repairs done during prep, with the whole slab accessible, are faster and cheaper than call-backs after coating. If budget forces a split, do Priorities 1 and 2 now and revisit the coating once the slab is stable — a coating installed over unresolved problems is money spent twice.
Every floor we install is backed by a written warranty on workmanship, so if a repair or coating doesn't hold up as it should, it's on us to put right — not a conversation about fine print.
If you're staring at a slab with all three problems at once, send us a few photos and a floor plan through the quote form on our website. We'll tell you what gets repaired first, what can wait, and what the coating options are for the slab you actually have.
Ready to move? Submit the quote form and we'll come back with a repair sequence and coating recommendation for your floor.