Control joints and why they are treated separately

If you manage a facility with a concrete slab, control joints are part of your daily reality. Understanding control joints and why they are treated separately from the rest of a concrete floor coating project will save you arguments, change orders, and disappointment down the line. The short version: control joints move. The rest of the slab mostly does not. Any coating system installed across a moving joint has to handle that movement, and that changes how the joint is prepared, what materials go into it, and how the warranty treats it.

What control joints actually do

Concrete shrinks as it cures and expands and contracts with temperature changes. Control joints — also called contraction joints — are deliberate grooves or saw cuts in the slab that create weak planes. Instead of the concrete cracking in random places, it cracks neatly inside the joint where you can't see it.

That's their whole job. They are not decorative. They are not optional. And critically, they are movement points: the two sides of a control joint can open, close, and shift slightly against each other for the life of the slab.

Expansion joints (sometimes called isolation joints) are a related but different animal. These are full-depth separations, often filled with backer rod and sealant, that isolate the slab from walls, columns, foundations, and other pours. They move more and are always treated on their own.

Why they can't just be coated over

Here's where inexperienced installers cause problems. A bare control joint is a visible line in the floor. An owner looks at it and asks, understandably, "Can you make that disappear?"

No — not permanently, and not honestly.

If you bridge a control joint with a rigid coating like standard epoxy flooring and fill it flush, the joint keeps moving underneath. The coating above it cracks, chips, or delaminates. This isn't a defect in the epoxy; it's the epoxy doing exactly what rigid materials do when stretched. Any bid that promises a seamless, joint-free look across active control joints is either planning to fail or planning to upsell you later.

How a proper installation treats them

A competent concrete floor coating project treats control joints as their own work scope:

Reconstruction (optional, common in warehouses). The saw cut is routed out, cleaned, and filled with a semi-rigid epoxy or polyurea joint filler. This restores edge support so forklift wheels don't chip the joint shoulders, and it's firm enough to protect the joint without fighting its movement. The filler is usually installed slightly recessed or flush, not proud of the surface.

Sealing (for joints that must stay flexible). Expansion joints and some control joints get a flexible polyurethane or polyurea sealant over backer rod. This keeps water and debris out while allowing movement.

Detailing at the coating stage. The coating is then installed up to the filled or sealed joint. The joint line remains visible — often as a clean, straight line — but it's protected and won't tear the coating apart.

Cost drivers, briefly

Joint treatment is usually priced per linear metre because it's labour-intensive precision work, not broad-area application. What drives the cost:

Expect joint treatment to be a separate line item on any legitimate quote, not folded invisibly into the floor price. If it's not on the quote, ask where it went.

What this means for your warranty

Joint-related issues are treated separately under warranty for the same reason they're treated separately in the work itself. A properly filled control joint can still show minor hairline separation or movement at the joint line — that's the material doing its job. Structural cracks, delamination of the coating in field areas, or filler that pulls loose are different matters. Our written warranty on installed floors covers workmanship; ask for the specific terms in writing before signing anything, and make sure joint treatment scope is spelled out in the contract, not assumed.

Questions to ask any contractor

  1. Will control joints be filled, sealed, or left open — and why?
  2. What material will be used, and is it semi-rigid or flexible?
  3. Is joint treatment itemised separately on the quote?
  4. What does the joint line look like when you're finished — flush, recessed, or bridged?
  5. How does the warranty treat movement at joints versus coating failure?

If a contractor bridges active control joints with rigid material and calls it a seamless system, walk away. The cracks will show up within the first season of temperature swings, and you'll be paying twice.

Get a quote that treats joints properly

Every slab is different. Send us the details of your floor through the quote form on our website — slab size, joint layout, current condition, and how the space is used — and we'll price the joint work as its own scope, alongside the coating. No surprises, no cracked joints six months later.