Flake and Chip Epoxy Floors

If you've been researching floor coatings for a garage, workshop, basement, or commercial space in Metro Detroit, you've probably run across flake and chip epoxy floors — and for good reason. They're one of the most durable and forgiving floor systems you can install, and they handle Michigan's freeze-thaw cycles, road salt, and heavy foot traffic better than almost any alternative. This page is a straight, practical guide: what flake and chip epoxy floors actually are, when a property needs them, what a proper installation includes, what drives the cost, and how to get an on-site assessment from Best Choice Epoxy Floors.

What Flake and Chip Epoxy Floors Are

A flake and chip system is a multi-layer resinous floor. In simple terms:

  1. Base coat. A primer or pigmented epoxy layer is applied to the prepared concrete. This is the layer that bonds the whole system to the slab.
  2. Flakes (chips). While the base coat is still wet, decorative vinyl chips are broadcast across the surface, either lightly or to full saturation. The flakes come in blends of several colors, so you can match or complement the rest of the space.
  3. Scrape and sand. Once cured, the surface is scraped and sanded to knock down loose flakes and leave an even, textured finish.
  4. Topcoat(s). One or more clear coats — typically polyaspartic or polyurethane — are rolled over the flakes. The topcoat locks everything in and provides the wear surface, UV stability, and chemical resistance.

The result is a floor that hides dirt, tire marks, and minor imperfections far better than a solid-color coating, while still being fully sealed and easy to clean.

Why the Texture Matters: Slip Resistance

One of the most common questions we get is whether an epoxy floor is slippery. A smooth, glossy coating can be. A flake system is different: the chips create a naturally textured surface, and the flakes sit at slightly different heights under the topcoat. That texture gives shoes and tires something to grip, which is why a flake floor reads as noticeably less slippery than a smooth-coated floor in the same conditions.

If a space needs more grip — a commercial kitchen, a ramp, an area that gets wet often — additional texture can be broadcast into the topcoat as well. This is something to bring up during the on-site assessment, because the right amount of texture depends on how the space is actually used.

When a Property Needs Flake and Chip Floors

Flake and chip epoxy floors are a fit in a few common situations:

If none of those apply and you just want a simple, budget-conscious sealed floor with no decorative element, a solid-color epoxy or clear sealer may be the better call. We'll tell you that during the assessment — flake isn't always the right answer, and selling it when it isn't is a waste of your money.

What a Proper Installation Includes

A flake floor is only as good as what happens before the flakes go down. Here's what a complete Best Choice Epoxy Floors installation includes:

Concrete preparation

The slab is mechanically ground or shot-blasted to open the surface and remove old coatings, curing compounds, oil, and contaminants. Coating over unprepared concrete is the single most common cause of peeling floors, and it's not a step that can be shortcut.

Crack and surface repair

Visible cracks, pop-outs, and spalled areas are repaired before coating. This doesn't mean every slab becomes cosmetically perfect — old slabs can have movement or discoloration that shows through any coating — but structural and surface defects are addressed so the floor performs.

Moisture assessment

Slabs in Metro Detroit basements and older buildings can hold moisture that pushes coatings off from below. If there are signs of moisture issues, that gets flagged and discussed before any coating is scheduled. Coating a wet slab is throwing money away.

Base coat and flake broadcast

Pigmented base coat applied and flakes broadcast into it. You choose the flake blend — see below — and the coverage level (full broadcast is standard for garages and commercial work).

Scrape, sand, and topcoat

Cured flakes are scraped and the surface is sanded smooth, then sealed with clear topcoat(s). Topcoat choice and number of coats depend on the environment — residential garage versus shop floor versus commercial space.

Written warranty

Installed floors come with a written warranty on workmanship. The terms are spelled out on paper, not just spoken, so you know exactly what's covered and for how long before the work starts.

Choosing a Flake Blend

Blend selection is done from physical samples, not from a screen. Photos of flakes on a website or phone never quite match the real thing — flake colors shift depending on lighting, background coat, and viewing angle. During the assessment, you'll look at actual sample boards, and you can take samples into the actual space to see how they read under your lighting.

A few practical notes on choosing:

Take your time with this step. It's the only part of the project you'll see every day; everything else is under the surface.

How Best Choice Epoxy Floors Performs the Work

Every job follows the same sequence:

  1. On-site assessment. We look at the slab, check for moisture and cracking, measure the space, and talk through how the floor will be used. This is where texture, topcoat, and repair scope get decided.
  2. Written quote. You receive a written quote based on the actual conditions, not a per-square-foot guess over the phone. No firm number can honestly be given without seeing the slab.
  3. Scheduling. Work is scheduled around weather and your operational needs. For commercial clients, work can be phased or scheduled over weekends/downtime where the system allows — this is discussed during the assessment.
  4. Preparation and coating. As outlined above: grind, repair, coat, flake, scrape, topcoat. Prep dust is managed with vacuums and containment.
  5. Cure and walkthrough. You get clear guidance on when the floor can be walked on, when furniture or vehicles can go back, and when it reaches full cure. We walk the finished floor with you before we call it done.

What Drives the Cost

We don't publish firm prices because two slabs of the same square footage can be very different jobs. Here's what actually moves the number:

As a general rule, expect flake systems to run somewhere between a basic solid-color epoxy and a high-end metallic or multi-build commercial system. If a quote seems dramatically cheaper than others, the difference is almost always in prep and material quality — the two things you can't see once the floor is done.

How Scheduling Works

Typical timeline for a residential garage: prep and coating over one to two days of on-site work, with light foot traffic within a day or two and vehicles back on the floor after the topcoat has had its recommended cure period. Commercial jobs vary more with size, phasing, and downtime windows.

Factors that affect scheduling:

You'll get a realistic date range at quote time, not an optimistic one.

Flake vs. Solid Color vs. Metallic — a Quick Comparison

Flake and chip Solid color epoxy Metallic
Hides dirt and imperfections Excellent Poor Good
Slip resistance (built-in texture) Yes Only if added Smooth unless textured
Repair/disguise of slab flaws Excellent Poor Moderate
Typical cost tier Mid Lowest Highest
Best for Garages, shops, light commercial Budget/utility floors Showrooms, retail

Common Questions

How long does a flake floor last? With proper prep and a quality topcoat, a residential garage floor typically lasts many years before a refresh of the topcoat is worth considering. Commercial life depends on traffic and abuse. The written warranty spells out our commitment on workmanship.

Can you coat over an existing epoxy floor? Sometimes, depending on what's down there and how well it's bonded. It's usually assessed during the on-site visit.

Will hot tires peel the floor? Hot-tire pickup is a symptom of poor bonding — usually inadequate prep or the wrong primer. A properly prepared and primed floor handles hot tires.

Is it messy? The grinding stage produces dust, but we use vacuum-equipped equipment and contain the work area. There's some odor during application; the space should be ventilated and vacated during coating hours.

Can I DIY it? Kits exist, but the two failure points — prep quality and material quality — are exactly the things DIY kits compromise on. Most DIY floors we end up recoating failed at the bond line, not the surface.

Serving Metro Detroit

Best Choice Epoxy Floors installs flake and chip epoxy floors throughout the Metro Detroit area — Oakland, Macomb, and Wayne County communities and surrounding suburbs. Local conditions matter here: freeze-thaw movement, salt exposure, and older slabs are all standard considerations in our assessments, not surprises.

Request an On-Site Assessment

The only way to get an honest number on a flake floor is to have someone look at your actual slab. Here's how it works:

  1. Submit the quote form on our website. Include your location, approximate square footage, what the space is used for, and anything you know about the slab (age, existing coatings, visible cracks).
  2. We schedule an on-site assessment. We inspect the concrete, check for moisture and cracks, and bring flake samples so you can choose a blend in your own lighting.
  3. You receive a written quote with the full scope, the written warranty terms, and a realistic schedule.

No phone tag, no high-pressure follow-up. Fill out the quote form on this site and we'll take it from there.


Ready for a floor that hides the dirt, resists the salt, and stops the dust? Submit the quote form on our website to request your free on-site assessment for flake and chip epoxy floors in Metro Detroit.